Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-216/16
Our 200QJH20-216/16 is a 16-stage deep well submersible pump for reservoir filling and irrigation water supply. A 25 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 216 m. The unit is installed vertically in the borehole and works below the water surface.
Water enters at the inlet section and is lifted stage by stage through the impellers and diffusers before leaving through the 2.5 inch outlet. The hydraulic components are cast stainless steel.
The 200QJ20 series covers a wide head range at the same 20 m³/h nominal flow. If the required head changes during project design, we will compare suitable models and recheck the installation dimensions, pipework and electrical requirements.
The pump is used for filling an irrigation reservoir or a storage tank from a borehole, and for supplying water to an irrigation system where the well lift and the delivery point together fit its head capability.
It is selected for clean groundwater service. Where the water is aggressive, the material grade and component scope are fixed in the quotation.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. Well Depth and Required Pump Head Are Different. Select the pump using the pumping water level and the delivery requirements. The required total head includes the vertical lift from the pumping water level to the delivery point, pipeline friction losses and any pressure required at the outlet. The total drilled depth of the well alone does not determine the required pump head. Static water level, pumping water level and planned installation depth are requested separately because one cannot replace another.
3. Well diameter is confirmed from the drawing. The 2.5 inch figure is the discharge connection, not the outside diameter of the pump. The 200 in the model name identifies the catalog series. The required borehole diameter is confirmed from the installation drawing for the selected assembly.
The motor rating for this model is 25 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. How do I know whether this model fits my well?
Send the required flow, total head, well depth and water levels. We check the operating point on the performance curve for the quoted configuration.
2. Can the pump run at the maximum catalog flow and maximum catalog head together?
No. Those are catalog range limits for this model. The required operating point must be checked against the performance curve, and the two maximums are not a guaranteed combined operating point.
3. Which stainless steel grade will be supplied?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
4. What is included with the pump?
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
5. What should we send with the enquiry?
The flow and total head, well data, water levels, pipeline data, supply voltage, frequency and phase, quantity and destination.
To assess this model and prepare a quotation, please send us:
You can leave any item you do not know blank. We will check the operating point on the performance curve and reply with the configuration, price and lead time.
Send your inquiry directly to us