Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-391/29
Our 200QJH20-391/29 is a 29-stage deep well submersible pump for deep borehole irrigation. A 45 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 391 m. At this depth the pumping water level, not the static level, sets the head, and the difference between the two can be large when the well yield is modest.
The hydraulic components are cast stainless steel, giving the twenty-nine stage stack a rigid bowl. Water enters at the inlet section, is lifted stage by stage and leaves through the 2.5 inch outlet.
Because the pump sits deep, the lifting plan, the cable length and the voltage drop all become design items rather than details. The pump itself is only one part of a working deep borehole installation.
Deep borehole irrigation is the main application: a low water level, a long rising main and a field that still needs pressure. The 391 m nominal head is aimed at that combination, and the flow stays at 20 m³/h as it does across the family.
It is also used for filling storage where the tank is high and the well is deep, and for supply points where the drawdown during pumping is the largest single part of the head.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. Use the pumping water level, not the static level. Total head is the pumping water level below the wellhead, plus the delivery elevation, plus the friction loss in the rising main and the field line. Calculating from the static level instead of the pumping level can lead to a pump that is undersized for the installation.
3. Electrical data is confirmed for the assembly. The motor rating, rated current, cable and protection are confirmed for the selected assembly. Cable length and conductor size are selected according to the complete cable route, supply voltage, voltage drop and installation requirements.
The motor rating for this model is 45 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. How do I know the pumping water level?
It comes from a pumping test on the borehole. If only the static level is known, the drawdown has to be estimated, and we would rather check it with real test data.
2. Can the pump be installed deeper than the water level?
The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly. The setting depth is confirmed from the well data.
3. Does the price include a dry running protector?
No. Protection and control are quoted with the installation, because they depend on the site and the starting method.
4. Which stainless steel grade will be supplied?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
5. What do you need to quote?
Required flow and total head, well diameter and depth, static and pumping water levels, delivery elevation, supply voltage and frequency, quantity and destination.
To select the right build and give you a firm quotation, please send us:
You can leave any item you do not know blank. We will confirm the duty point on the curve and reply with the configuration, price and lead time.
Send your inquiry directly to us