Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-365/27
Our 200QJH20-365/27 is a 27-stage deep well submersible pump for high head irrigation supply. A 45 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 365 m. It is chosen when the pumping water level is deep and the field line still needs pressure at the far end, so the head budget is long on both sides of the wellhead.
The hydraulic components are cast stainless steel, which gives the bowl the rigidity a twenty-seven stage stack needs. Water enters at the inlet section, passes through the impellers and diffusers in series and leaves through the 2.5 inch outlet into the rising main.
This model keeps the 20 m³/h nominal flow of the 200QJ20 family and the same outlet size as the lower-head versions. What changes is the number of stages, the motor size and the cable cross-section, and those three decide the electrical and lifting plan for the installation.
High head irrigation supply is the main duty: a deep well, a long rising main and a field line that has to hold pressure at the furthest outlet. The 365 m nominal head is aimed at that combination, where the drawdown alone can take a large part of the total.
The model is also used for filling high-level storage and for supply points that combine irrigation with stock or domestic demand, provided the duty point and the control arrangement are checked together.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. Drawdown and mainline losses both count. Total head is the pumping water level below the wellhead, plus the delivery elevation, plus the friction loss in the rising main and the field line. On a high head job the last item is often underestimated, especially where the pipe diameter is small.
3. Electrical data is confirmed for the assembly. The motor rating, rated current, cable and protection are confirmed for the selected assembly. Cable length and conductor size are selected according to the complete cable route, supply voltage, voltage drop and installation requirements.
The motor rating for this model is 45 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. Why choose this model instead of the 351 m version?
It has one more stage and a higher nominal head, with the same 45 kW motor, 20 m³/h nominal flow and 2.5 inch outlet. The choice follows the confirmed total head.
2. Can the pump run on a long cable run?
It can, if the cross-section is increased to keep the voltage drop within limits. Send the distance from the transformer to the well and we will confirm the cable size with the order.
3. Is a soft starter required?
It depends on the supply capacity and the starting current allowed at site. The starting method is confirmed in the quotation.
4. Which stainless steel grade will be supplied?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
5. What do you need to quote?
Required flow and total head, well diameter and depth, water levels, delivery elevation, pipeline length and diameter, supply voltage and frequency, quantity and destination.
To select the right build and give you a firm quotation, please send us:
You can leave any item you do not know blank. We will confirm the duty point on the curve and reply with the configuration, price and lead time.
Send your inquiry directly to us