Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-378/28
Our 200QJH20-378/28 is a 28-stage deep well submersible pump for mountain farmland irrigation. A 45 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 378 m. On terraced land the delivery elevation is the dominant part of the head, because the water has to climb from the well to fields that sit well above it.
The hydraulic components are cast stainless steel. Water is drawn in at the inlet section, lifted through twenty-eight stages and discharged through the 2.5 inch outlet into a rising main that runs up the slope.
A long rising main up a hillside adds friction loss on top of the static lift, and the pipe diameter matters as much as the pump. This is why the full installation layout, not just the well, belongs in the selection.
Mountain farmland irrigation is the main application: lifting water from a valley borehole to terraced fields, with the delivery point high above the wellhead. The 378 m nominal head covers that static lift plus the friction in a long, inclined rising main.
It is also used for filling hilltop storage tanks that then feed the terraces by gravity, a layout that lets the pump run at a steady point instead of following the field demand.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. The rising main up the slope is part of the head. Give us the vertical lift, the pipe length, the diameter and the number of bends. On a hillside layout the friction loss in a long inclined main can be a significant share of the total.
3. Electrical data is confirmed for the assembly. The motor rating, rated current, cable and protection are confirmed for the selected assembly. Cable length and conductor size are selected according to the complete cable route, supply voltage, voltage drop and installation requirements.
The motor rating for this model is 45 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. How high can this pump lift water?
The nominal head is 378 m, and the catalog range listed for this model extends to 435 m. The usable lift depends on the flow you need, because flow and head move in opposite directions along the curve.
2. Can it feed a tank on the hill and the terraces at the same time?
It can feed a tank, and the terraces can then be supplied from that tank. Direct supply to both points at once has to be checked as one duty point.
3. Is the pipe diameter important?
Yes. A long inclined main with a small diameter adds friction loss that has to be paid for in head, so the pipe size is part of the selection.
4. Which stainless steel grade is used?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
5. What information do you need?
Required flow and total head, vertical lift, pipeline length and diameter, well data, supply voltage and frequency, quantity and destination.
To select the right build and give you a firm quotation, please send us:
You can leave any item you do not know blank. We will confirm the duty point on the curve and reply with the configuration, price and lead time.
Send your inquiry directly to us