Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-405/30
Our 200QJH20-405/30 is a 30-stage deep well submersible pump for high lift water supply. A 45 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 405 m. It is the highest head model in the 200QJ20 family, so it is selected when the total lift cannot be met by any lower stage count at the same flow.
The hydraulic components are cast stainless steel, which keeps the thirty stage stack rigid at high head. Water enters at the inlet section, passes through the impellers and diffusers and leaves through the 2.5 inch outlet.
Thirty stages also mean a longer, heavier unit. The installation has to be planned around that: sling capacity, tripod height, setting depth measurement and the cable length are all part of getting the pump into the well correctly.
High lift water supply is the main application: a deep well, a high delivery point, or both, where the total head is beyond the lower models in the family. The 405 m nominal head covers that lift at the same 20 m³/h flow as the rest of the range.
It is also used for filling elevated storage and for irrigation layouts where the field is far above the water level. In both cases the head budget is dominated by static lift rather than by the field network.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. This is the end of the 20 m³/h family. If the confirmed head is above the range of this model, the correct answer is a different family or a different flow, not a larger number on the same page. We check that before quoting.
3. Thirty stages need a proper handling plan. The assembled length and weight require the right sling, tripod and setting depth measurement. Cable length and voltage drop are confirmed with the order, because the setting is usually deep on this duty.
The motor rating for this model is 45 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. Is this the highest head model in the family?
Yes, for the 200QJ20 range at 20 m³/h nominal flow. If you need more head, we would look at another family or a different flow rather than stretch this model.
2. Can it be supplied for a 50 Hz and a 60 Hz project?
Yes. Both builds are available, and each uses its own performance data, so please state the frequency at site.
3. What is the installation weight and length?
That depends on the final configuration. We confirm the handling data with the approved drawing before shipment.
4. Which stainless steel grade is used?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
5. What should we send for a quotation?
Required flow and total head, well diameter and depth, water levels, delivery elevation, pipeline data, supply voltage and frequency, quantity and destination.
To select the right build and give you a firm quotation, please send us:
You can leave any item you do not know blank. We will confirm the duty point on the curve and reply with the configuration, price and lead time.
Send your inquiry directly to us