Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-270/20
Our 200QJH20-270/20 is a 20-stage deep well submersible pump for water supply from deeper boreholes. A 30 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 270 m. The twenty stages lift the water further than the lower-head models in the family while keeping the same 20 m³/h nominal flow and the same 2.5 inch outlet.
The hydraulic components are cast stainless steel, which gives the bowl the rigidity that a high stage count needs. Water enters at the inlet section, passes through the impellers and diffusers in series, and leaves through the outlet into the rising main.
This model sits near the upper end of the 200QJ20 range that still uses the 30 kW motor. Above it, the family moves to 37 kW and 45 kW motors with larger cable, so the electrical design and the lifting equipment have to be reviewed at the same time as the pump selection.
The main application is deep well water supply: lifting water from a borehole into an elevated tank, a village main, or a farm distribution line where the pumping water level is deep and the delivery point is well above the wellhead. The 270 m nominal head accounts for that lift plus the line losses.
It is also used as the supply pump for irrigation systems that need a higher pressure at the main line, and for filling storage where the fill point is high on the site.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. Twenty stages need a clean lifting plan. The assembled length and weight of a twenty-stage unit must be handled with the right sling and tripod, and the setting depth has to be measured before installation. This is a site planning point, not a pump performance point, but it decides whether the installation goes smoothly.
3. Electrical data is confirmed for the assembly. The motor rating, rated current, cable and protection are confirmed for the selected assembly. Cable length and conductor size are selected according to the complete cable route, supply voltage, voltage drop and installation requirements.
The motor rating for this model is 30 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. What is the difference between the 256 m and 270 m models?
One more stage and a higher nominal head, with the same 30 kW motor, 20 m³/h nominal flow and 2.5 inch outlet. The choice depends on the confirmed total head of the installation.
2. Can the pump be installed in an existing borehole?
Yes, if the borehole diameter, depth and water levels suit the exact build. We confirm the required well diameter from the installation drawing rather than from the model prefix.
3. Is a variable frequency drive required?
Not required, but it can be quoted if the supply or the operating range calls for it. The drive is an accessory and is priced with the order.
4. Which stainless steel grade is supplied?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
5. What should we send with the enquiry?
Required flow and total head, well diameter and depth, water levels, delivery elevation, supply voltage and frequency, cable length, quantity and destination.
To select the right build and give you a firm quotation, please send us:
You can leave any item you do not know blank. We will confirm the duty point on the curve and reply with the configuration, price and lead time.
Send your inquiry directly to us