Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-283/21
Our 200QJH20-283/21 is a 21-stage deep well submersible pump for orchard irrigation. A 30 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 283 m. In an orchard the water usually has to be lifted from the well and then pushed across a wide area, so the head budget is dominated by the delivery elevation and the length of the main line rather than by a single sprinkler block.
The hydraulic components are cast stainless steel, which gives the bowl the rigidity that twenty-one stages need. Water enters at the inlet section, passes through the impellers and diffusers in series and leaves through the 2.5 inch outlet into the rising main.
This model uses the 30 kW motor, the middle step of the 200QJ20 family. The models below it in head run on 25 kW, and the models above move to 37 kW with a larger cable, so this is the last point where the lighter electrical package can still cover the duty.
Orchard irrigation is the main duty: the pump lifts water from the borehole and feeds a main line that runs along the rows, with hydrants or drip lines branching off. A mature orchard needs a steady volume over a long irrigation window, which matches the flat part of the pump curve rather than a single peak point.
The same model is used for filling farm storage and for supplying a mixed irrigation layout where the head requirement is a little above the 256 m and 270 m versions but the flow stays at 20 m³/h.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. Main line length is part of the head. For an orchard the friction loss along the main line and through the valves and hydrants can be a large share of the total. Give us the line length, the pipe diameter and the number of outlets, and we will include those losses in the check.
3. Electrical data is confirmed for the assembly. The motor rating, rated current, cable and protection are confirmed for the selected assembly. Cable length and conductor size are selected according to the complete cable route, supply voltage, voltage drop and installation requirements.
The motor rating for this model is 30 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. Can one pump serve several orchard blocks?
Yes, if the total head at the furthest block is still inside the curve. Send the layout, the pipe sizes and the number of outlets, and we will check the worst-case block.
2. Does the price include the cable and control panel?
No. The pump is quoted as the unit; cable, starter and control panel are quoted according to the installation.
3. Which stainless steel grade will be supplied?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
4. Can the pump be run from a generator?
That depends on the generator capacity and the starting method. Tell us the supply available at site and we will confirm the starting arrangement in the quotation.
5. What should we send to get a quotation?
Required flow and total head, well data, pipeline length and diameter, supply voltage and frequency, quantity and destination.
To select the right build and give you a firm quotation, please send us:
You can leave any item you do not know blank. We will confirm the duty point on the curve and reply with the configuration, price and lead time.
Send your inquiry directly to us