Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-310/23
Our 200QJH20-310/23 is a 23-stage deep well submersible pump for village and community water supply. A 37 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 310 m. Village supply usually means a deep static level, a tank on high ground or a tower, and a daily demand that peaks in the morning and evening.
The hydraulic components are cast stainless steel. Water enters at the inlet section, is lifted through twenty-three stages and leaves through the 2.5 inch outlet. The pump is installed below the water surface and must operate within the submergence and motor cooling conditions specified for the selected assembly.
Because the flow stays at 20 m³/h across the 200QJ20 family, this model can be matched to the same rising main and tank as the lower-head versions; what changes is the head per stage and the motor size behind it.
The main application is village or community water supply: filling an elevated tank that then feeds a distribution network, or pumping directly into a mains line during set hours. The 310 m nominal head covers the deep pumping level plus the lift to the tank or the top of the network.
It is also used for institutional supply at farms, schools and small industrial sites where a borehole is the only source and the demand is steady across the day.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. Tank height and drawdown both count. Total head is the pumping water level below the wellhead, plus the delivery elevation, plus the friction loss in the rising main and the network. The drawdown during pumping is the figure most often left out of a village supply calculation.
3. Electrical data is confirmed for the assembly. The motor rating, rated current, cable and protection are confirmed for the selected assembly. Cable length and conductor size are selected according to the complete cable route, supply voltage, voltage drop and installation requirements.
The motor rating for this model is 37 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. Can the pump work with a level control in the tank?
Yes. Float or electrode level control is part of the control requirements and is quoted with the installation.
2. What happens if the village demand is lower than 20 m³/h?
The pump can run into a tank and stop on level, which decouples pump flow from hourly demand. If the demand is much lower for long periods, a smaller flow model in the family may suit better.
3. Is the motor housing stainless steel?
The hydraulic components are cast stainless steel. The motor housing follows the configuration confirmed for the project and is stated in the quotation.
4. Which stainless steel grade will be supplied?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
5. What do you need to quote?
Required flow and total head, well diameter and depth, water levels, tank height, supply voltage and frequency, cable length, quantity and destination.
To select the right build and give you a firm quotation, please send us:
You can leave any item you do not know blank. We will confirm the duty point on the curve and reply with the configuration, price and lead time.
Send your inquiry directly to us