Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-324/24
Our 200QJH20-324/24 is a 24-stage deep well submersible pump for farm irrigation distribution. A 37 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 324 m. It is aimed at layouts where one pump feeds a distribution network with several outlets rather than a single block, so the head has to hold when outlets are opened and closed.
The hydraulic components are cast stainless steel. Water is drawn in at the inlet section, lifted stage by stage through twenty-four impellers and diffusers, and discharged through the 2.5 inch outlet into the rising main.
On a distribution network the pump rarely runs at exactly its nominal point. The curve shows how much head remains as flow increases, and that shape matters more than a single catalogue figure when several hydrants are in use at once.
Farm irrigation distribution is the main application: the pump feeds a buried network with hydrants or valves that open in sequence, and the pressure at the furthest outlet has to stay usable while the nearer ones are running. The 324 m nominal head gives margin for that variation.
The model is also used for filling a storage tank that then supplies the network by gravity, which is a common way to keep the pump running at a stable point instead of following the field demand.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. Distribution losses are part of the head. Give us the network layout, the pipe diameters, the number of open outlets and the pressure needed at the furthest one. Those losses, added to the pumping water level and the delivery elevation, make up the total head the pump must produce.
3. Model prefix is not the pump diameter. The 200 identifies the catalogue series, and the 2.5 inch figure is the discharge connection. The required borehole diameter is confirmed from the installation drawing for the exact build.
The motor rating for this model is 37 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. Can the pump hold pressure when outlets close?
The pressure rises as flow falls, which is normal for this type of pump. The control arrangement, such as a pressure switch or a bypass, is decided with the installation and quoted with the order.
2. How many hydrants can run at once?
That depends on their flow and the network losses. Send the layout and we will check the worst combination against the curve.
3. Does the quotation include the cable and starter?
No. They are priced according to the installation, because cable length and starting method depend on the site.
4. What stainless steel grade is supplied?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
5. What is needed for a quotation?
Required flow and total head, well data, network layout and pipe sizes, supply voltage and frequency, quantity and destination.
To select the right build and give you a firm quotation, please send us:
You can leave any item you do not know blank. We will confirm the duty point on the curve and reply with the configuration, price and lead time.
Send your inquiry directly to us