Place of Origin:
China
Brand Name:
SLAPK
Certification:
CE, ISO9001
Model Number:
200QJH20-338/25
Our 200QJH20-338/25 is a 25-stage deep well submersible pump for irrigation from wells with a low pumping water level. A 37 kW motor drives it at a nominal flow of 20 m³/h and a nominal head of 338 m. At this stage count the pump is working near the upper half of the 200QJ20 family, and the head budget is driven mainly by the depth to water rather than by the field layout.
The hydraulic components are cast stainless steel. Water enters at the inlet section, is lifted through twenty-five stages and leaves through the 2.5 inch outlet. The unit is installed below the water surface and must operate within the submergence and motor cooling conditions specified for the selected assembly.
Because the family keeps 20 m³/h across the range, this model can be exchanged with a lower or higher head version without changing the outlet size or the rising main, provided the motor and cable are reviewed at the same time.
Deep well irrigation is the main application: the static and pumping water levels are low, and the pump has to produce enough head to lift the water to the surface and still push it through the field line. The 338 m nominal head is aimed at that combination.
It is also used for filling high-level storage on a site where the tank or reservoir sits well above the wellhead, and for supply points that combine irrigation with stock water.
The hydraulic components are manufactured by casting. The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
1. Catalog ranges and the operating point. The flow and head figures above are the catalog ranges listed for this model. The required operating point must be checked against the performance curve for the quoted configuration. The maximum catalog flow and maximum catalog head should not be combined as a guaranteed operating point.
2. Drawdown decides the real head. On a deep well the pumping water level can be well below the static level. Total head has to be calculated from the pumping level, not the static level, plus the delivery elevation and the pipe losses.
3. Twenty-five stages change the handling. The assembled length and weight need a proper sling, tripod and setting depth measurement before installation. That is a site planning point, but it decides whether the unit goes in cleanly.
4. Electrical data is confirmed for the assembly. The motor rating, rated current, cable and protection are confirmed for the selected assembly. Cable length and conductor size are selected according to the complete cable route, supply voltage, voltage drop and installation requirements.
The motor rating for this model is 37 kW. Please provide the supply voltage, frequency and phase. The motor rating, rated current and electrical configuration will be confirmed for the selected assembly. Performance data will correspond to the specified frequency.
Cable length and conductor size are selected according to the complete cable route, motor rating, supply voltage, voltage drop and installation requirements. The supplied cable specification will be stated in the quotation.
Each pump is built to the configuration confirmed on the order, tested at our works before packing, and released for delivery after it passes.
The quotation will specify the supplied motor lead cable, any extension cable, control equipment and accessories.
Do not run the pump dry. The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly.
The minimum order quantity is to be confirmed in the quotation. Lead time will be stated in the quotation based on the order configuration and quantity. Warranty terms will be specified in the quotation. Packing is specified in the quotation.
1. My static water level is deep. Is this model suitable?
It can be, but the pumping water level matters more than the static level. Send both figures plus the well yield, and we will check the duty point.
2. What is the maximum setting depth?
The installation must maintain the minimum submergence and motor cooling conditions specified for the selected assembly. We confirm the setting depth from the well data and the installation drawing.
3. Is a VFD recommended for a deep setting?
Not automatically. It is quoted when the supply or the operating range calls for it, and the decision is made with the electrical data at site.
4. Which stainless steel grade will be used?
The stainless steel grade and component scope are specified in the quotation according to the water quality and project requirements.
5. What information do you need?
Required flow and total head, well diameter and depth, static and pumping water levels, delivery elevation, supply voltage and frequency, quantity and destination.
To select the right build and give you a firm quotation, please send us:
You can leave any item you do not know blank. We will confirm the duty point on the curve and reply with the configuration, price and lead time.
Send your inquiry directly to us